DataCard ImageCard Select Guía de usuario Pagina 84
- Pagina / 154
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7-4
Install the printer
User’s Guide for ImageCard® Select™ and UltraGrafix® Select™ Printers
Connect a parallel port data cable
1 Attach the parallel port cable to the ECP parallel port on the printer.
The parallel port cable must be a shielded, Type C, IEEE 1284 parallel port cable,
up to a maximum of 6.5 feet or 2 meters long.
Figure 7-2: Connect the parallel port cable
2 Attach the other end of the cable to the parallel port on the PC ( see Figure 7-2).
Press the cable connector all the way onto the port, and then turn the posts to
secure the cable to the PC.
Some parallel communication devices use a cable with a plug that allows
another device to be attached, so that two parallel devices are attached to
one PC parallel port, known as a pass-through or piggy-back plug. The printer
and printer driver cannot communicate reliably through such a plug. Install an
additional parallel port in the PC if needed.
♦
i
i
- User’s Guide for 1
- ImageCard® Select™ and 1
- UltraGrafix® Select™ 1
- Printers 1
- Regulatory compliance 2
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- Overview 7
- About this manual 8
- Audience 8
- About the Select printer 8
- Printer models 9
- 1-4 Overview 10
- Printer features 11
- 1-6 Overview 12
- 1-8 Overview 14
- • ECP parallel port 14
- • USB port 14
- Who to call for assistance 15
- 1-10 Overview 16
- Using the printer 17
- Loading cards 18
- Magnetic Stripe 19
- Smart Card Chip 19
- Loading the print ribbon 20
- Load the print ribbon 21
- Powering on the system 22
- Status light 23
- Making cards 24
- Print from a PC application 25
- Removing cards 26
- Responding to messages 27
- 2-12 Using the printer 28
- Fix a printer problem 28
- Shutting down the system 29
- 2-14 Using the printer 30
- Using the printer driver 31
- Tips for settings 32
- 3-4 Using the printer driver 34
- 3-6 Using the printer driver 36
- • Cleaning interval 36
- Use the Properties dialog box 37
- 3-8 Using the printer driver 38
- Using the Status Monitor 39
- Suspending the Status Monitor 41
- 3-12 Using the printer driver 42
- 3-14 Using the printer driver 44
- Maintaining the printer 45
- Running a cleaning cycle 46
- 4-4 Maintaining the printer 48
- Run a printer cleaning card 48
- Cleaning the printer rollers 50
- 4-8 Maintaining the printer 52
- Cleaning tips 53
- Cleaning the printhead 53
- 4-10 Maintaining the printer 54
- Power cable 56
- Ground cable 56
- 4-14 Maintaining the printer 58
- Troubleshooting 59
- Troubleshooting guide 60
- Make a printer test card 61
- 5-4 Troubleshooting 62
- Track Format Data 63
- 5-6 Troubleshooting 64
- Problems with card appearance 65
- Print Module 66
- 5-10 Troubleshooting 68
- 5-12 Troubleshooting 70
- Obtaining service 72
- When to obtain service 73
- Before you install 75
- Installation audience 76
- General requirements 76
- Selecting the site 77
- Environmental requirements 78
- Install the printer 81
- Unpacking the printer 82
- Connecting cables 83
- Connect a USB data cable 85
- Installing the printer driver 87
- 7-8 Install the printer 88
- 7-10 Install the printer 90
- 7-12 Install the printer 92
- Printing sample cards 95
- Setup tips 96
- Safety and compliance 99
- Liability statement 100
- Acknowledgments 101
- Supplies and cards 103
- Supply roll storage 104
- Card specifications 105
- Card size 105
- Card material 105
- StickICards 106
- New cards preferred 106
- Pre-punched cards 106
- Card quality guidelines 107
- Cleaning supplies 108
- Cleaning kits 109
- Magnetic stripe cleaning card 109
- Cleaning pen 109
- Printer driver CD-ROM 110
- Printer components 111
- Data cable 112
- Power cord 113
- Smart card serial cable 113
- Print ribbon cartridge 114
- Card cartridge 114
- Related publications 115
- PC settings 117
- Set up two ECP parallel ports 118
- • Setting USB port values 121
- Setting parallel port values 122
- Setting printer permissions 122
- Figure C-3: Ports dialog box 125
- Setting Value 125
- Magnetic stripe encoding 131
- NTT character set 132
- Magnetic Stripe Setup 133
- Installation messages 135
- Possible Cause Action 136
- Digital signature not found 144
- Numerics 147
Relacionado con productos y manuales para Impresoras De Etiquetas DataCard ImageCard Select
(25 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales