DataCard LM200 Guía de usuario Pagina 84
- Pagina / 109
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
78 SR200 & SR300 Printer and LM200 & LM300 Laminator User Guide
Jam (Retrans) There is a card jam near
the retransfer rollers.
1 Remove the jammed card from the retransfer
section.
2 Press Reset, and then Return to initialize the
printer.
3 See
“Retransfer section jam” on page 75.
Film Search The retransfer film is
broken or missing.
1 Repair the retransfer film as described in
“Mending
broken ink ribbon or retransfer film” on page 76
.
2 Press Reset, Next, and then Return to initialize the
film one panel.
Film Run Out The retransfer film has run
out.
1 Replace with new roll of retransfer film as
described in
“Load retransfer film” on page 11.
2 Initialize the new roll of film as described in
“Initialize the ink ribbon and retransfer film” on
page 17
.
Ink Search The ink ribbon is broken.
1 Repair the ink ribbon as described in
“Mending
broken ink ribbon or retransfer film” on page 76
.
2 Press Reset, Next, and then Return to initialize the
printer and supplies.
Ink Run Out The ink ribbon has run out. 1 Replace with a new roll of ink ribbon as described
in “Load ink ribbon” on page 10.
2 Press Reset, Next, and then Return to initialize the
printer and supplies.
Ink Error The ink ribbon is not
installed or the ribbon
installed is not supported.
1 Install a supported ink ribbon.
2 Press Reset, Next, and then Return to initialize the
printer and supplies.
Please Adjust Turn Unit
Pos!
The card turnover unit is
not in the correct position.
1 Turn the unit to the home position using a Jog Dial,
as described in “Turnover jam” on page 74.
2 Press Reset, and then Return to initialize the
printer. Call for service if the problem persists.
Cam Error Heat roller operation error. 1 Press Reset, and then Return to initialize the
printer.
2 Call for service if the problem persists.
No Card 1 There are no cards in
the card hopper.
2 The card hopper has
been removed.
1 Load cards as described in “Load cards” on
page 8.
2 Replace the card hopper securely as described in
“Replace the Hopper” on page 9.
Door Open The printer door is open, or
a supply cartridge or
cleaning unit is missing.
1 Insert all supply cartridges and the cleaning unit.
2 Close the printer door.
3 Press Reset, and then Return to initialize the
printer.
Hardware There is a hardware error. Turn the power switch off and then on again. Call for
service if the problem persists.
LCD Message Possible Cause Solution
- User Guide 1
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- 5 Messages 5
- Liability statement 6
- Introduction 7
- About the printer 8
- The inside of the printer 9
- The back of the printer 10
- About the laminator 11
- Using the printer 13
- Load Supplies 14
- Remove Hopper and Cards 15
- Replace the Hopper 15
- Adjust Card Thickness 15
- Load ink ribbon 16
- Load retransfer film 17
- Load top side laminate film 18
- Take-up Spool 19
- Supply Roll 19
- Guide Shaft 19
- Metal Guides 19
- Power on 20
- Optional laminator connection 21
- Power on the laminator 21
- Power on the printer 22
- Prepare to print cards 23
- Printing cards 23
- Print cards using ID software 24
- Print from a PC application 24
- Tips for Success 25
- Viewing and changing 27
- Printing Preferences 28
- Print tab 29
- Priority of Data 31
- 1 Panel Auto 2 Panels 31
- Page Split 32
- Security Erase 33
- Printing Area Settings 34
- Printer Settings 34
- Encode tab 35
- Laminate tab 35
- Configuration tab 35
- Printing Properties 36
- Status Monitor 37
- Close the Status Monitor 38
- Printer Status tab 39
- Printer Setting tab 40
- Retransfer tab 41
- Bend Remedy tab 42
- Media Setting tab 42
- Property tab 43
- Laminator tab 44
- Printer Select tab 45
- Others tab 46
- Security Lock tab 46
- Status monitor messages 47
- “Mending 49
- Using the LCD Menus 55
- Using the Printer LCD Panel 57
- Printer Security Number 63
- Red Status Light 64
- Blue Status Light 64
- Operator Button 64
- “Laminator 65
- LCD messages” on page 84 65
- Laminator Settings 66
- Taking care of your printer 67
- Cleaning the printer 68
- Tips – Cleaning card feed 69
- Cleaning the magnetic head 70
- Cleaning the thermal head 71
- Cleaning printer fan filters 71
- Cleaning the laminator 73
- Laminator fan filter 75
- Messages 77
- Printer error recovery 78
- Transfer jam 79
- Turnover jam 80
- Retransfer section jam 81
- Printer LCD messages 83
- “Operating environment” on 85
- “Load cards” on 85
- Take -up side 86
- Laminate pressure motor 86
- Supply side 86
- Supp ly Roll 87
- Patch Position 88
- Card warping 89
- Laminator LCD messages 90
- Supplies 93
- Ink ribbon 94
- Retransfer film 94
- Laminator material 95
- Cleaning supplies 96
- Site requirements 97
- Site guidelines 98
- Ventilation clearance 99
- Printer specifications 100
- Laminator specifications 101
- Magnetic Stripe Encoding 103
- Inline Encoding 104
- Character Code Table 105
- Compliance (FCC) 107
- Regulatory compliance 108
- 11111 Bren Road West 109
- Minnetonka, MN 55343-9015 109
- 952.933.1223 109
- 952.933.7971 FAX 109
© 2020, manymanuals.es. Todos los derechos reservados | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales