DataCard LM200 Guía de usuario Pagina 91
- Pagina / 109
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SR200 & SR300 Printer and LM200 & LM300 Laminator User Guide 85
HR-T Overheat Heating roller temperature
error (temperature is too
high).
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Overheat-T Internal temperature error
(temperature is too high).
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Heater-B Heater error. Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Heater-T Heater error. Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Thermistor-B Heating roller sensor
temperature error.
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Thermistor-T Heating roller sensor
temperature error.
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Cam-B Heating roller pressing
operation error.
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Cam-T Heating roller pressing
operation error.
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
HR-BTOverheat Heating roller temperature
error (temperature is too
high).
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Overheat-T Internal temperature error
(temperature is too high).
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Heater-T Heater error. Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Thermistor-T Heating roller sensor
temperature error.
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
Cam-T Heating roller pressing
operation error.
Turn the power switch off, and then back on. Contact
your service provider if this does not correct the
condition.
LCD Message Possible Cause Solution
- User Guide 1
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- 5 Messages 5
- Liability statement 6
- Introduction 7
- About the printer 8
- The inside of the printer 9
- The back of the printer 10
- About the laminator 11
- Using the printer 13
- Load Supplies 14
- Remove Hopper and Cards 15
- Replace the Hopper 15
- Adjust Card Thickness 15
- Load ink ribbon 16
- Load retransfer film 17
- Load top side laminate film 18
- Take-up Spool 19
- Supply Roll 19
- Guide Shaft 19
- Metal Guides 19
- Power on 20
- Optional laminator connection 21
- Power on the laminator 21
- Power on the printer 22
- Prepare to print cards 23
- Printing cards 23
- Print cards using ID software 24
- Print from a PC application 24
- Tips for Success 25
- Viewing and changing 27
- Printing Preferences 28
- Print tab 29
- Priority of Data 31
- 1 Panel Auto 2 Panels 31
- Page Split 32
- Security Erase 33
- Printing Area Settings 34
- Printer Settings 34
- Encode tab 35
- Laminate tab 35
- Configuration tab 35
- Printing Properties 36
- Status Monitor 37
- Close the Status Monitor 38
- Printer Status tab 39
- Printer Setting tab 40
- Retransfer tab 41
- Bend Remedy tab 42
- Media Setting tab 42
- Property tab 43
- Laminator tab 44
- Printer Select tab 45
- Others tab 46
- Security Lock tab 46
- Status monitor messages 47
- “Mending 49
- Using the LCD Menus 55
- Using the Printer LCD Panel 57
- Printer Security Number 63
- Red Status Light 64
- Blue Status Light 64
- Operator Button 64
- “Laminator 65
- LCD messages” on page 84 65
- Laminator Settings 66
- Taking care of your printer 67
- Cleaning the printer 68
- Tips – Cleaning card feed 69
- Cleaning the magnetic head 70
- Cleaning the thermal head 71
- Cleaning printer fan filters 71
- Cleaning the laminator 73
- Laminator fan filter 75
- Messages 77
- Printer error recovery 78
- Transfer jam 79
- Turnover jam 80
- Retransfer section jam 81
- Printer LCD messages 83
- “Operating environment” on 85
- “Load cards” on 85
- Take -up side 86
- Laminate pressure motor 86
- Supply side 86
- Supp ly Roll 87
- Patch Position 88
- Card warping 89
- Laminator LCD messages 90
- Supplies 93
- Ink ribbon 94
- Retransfer film 94
- Laminator material 95
- Cleaning supplies 96
- Site requirements 97
- Site guidelines 98
- Ventilation clearance 99
- Printer specifications 100
- Laminator specifications 101
- Magnetic Stripe Encoding 103
- Inline Encoding 104
- Character Code Table 105
- Compliance (FCC) 107
- Regulatory compliance 108
- 11111 Bren Road West 109
- Minnetonka, MN 55343-9015 109
- 952.933.1223 109
- 952.933.7971 FAX 109
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales