DataCard LM200 Guía de usuario Pagina 85
- Pagina / 109
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SR200 & SR300 Printer and LM200 & LM300 Laminator User Guide 79
HR Overheat The retransfer or bend
remedy roller is too hot.
Turn the power switch off and then on again. Call for
service if the problem persists.
TR Heater The retransfer roller is not
working.
Turn the power switch off and then on again. Call for
service if the problem persists.
TR Overheat The retransfer roller is too
hot.
Turn the power switch off and then on again. Call for
service if the problem persists.
TR Thermister The retransfer roller
thermistor is not working.
Turn the power switch off and then on again. Call for
service if the problem persists.
RR Overheat The bend remedy roller is
too hot.
Turn the power switch off and then on again. Call for
service if the problem persists.
RR Heater The bend remedy roller is
not working.
Turn the power switch off and then on again. Call for
service if the problem persists.
RR Thermister The bend remedy roller
thermistor is not working.
Turn the power switch off and then on again. Call for
service if the problem persists.
Overcool It is too cold for the printer
to operate.
The temperature in the printer area is too low. Use at
the recommended operating environment temperature
as described in “Operating environment” on
page 92
.
Head Overheat The thermal head is
overheated.
Turn the power switch off and allow the printer to cool
for approximately 10 minutes before turning power
back on.
Power Intrpt Power was interrupted for
a short time.
Turn the power switch off and then on again. Call for
service if the problem persists.
EEProm Broken EEPROM malfunction Turn the power switch off and then on again. Call for
service if the problem persists.
MG Unconnected Magnetic stripe module
connection error
Turn the power switch off and then on again. Call for
service if the problem persists.
MG Mechanical Magnetic stripe
mechanical error
Turn the power switch off and then on again. Call for
service if the problem persists.
MG Hardware Magnetic stripe hardware
error
Turn the power switch off and then on again. Call for
service if the problem persists.
MG Test Err A write error occurred
during self-test.
1 Check the type and orientation of magnetic cards in
the card hopper as described in
“Load cards” on
page 8
.
2 Press Reset, and then Return to initialize the
printer.
LCD Message Possible Cause Solution
- User Guide 1
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- 5 Messages 5
- Liability statement 6
- Introduction 7
- About the printer 8
- The inside of the printer 9
- The back of the printer 10
- About the laminator 11
- Using the printer 13
- Load Supplies 14
- Remove Hopper and Cards 15
- Replace the Hopper 15
- Adjust Card Thickness 15
- Load ink ribbon 16
- Load retransfer film 17
- Load top side laminate film 18
- Take-up Spool 19
- Supply Roll 19
- Guide Shaft 19
- Metal Guides 19
- Power on 20
- Optional laminator connection 21
- Power on the laminator 21
- Power on the printer 22
- Prepare to print cards 23
- Printing cards 23
- Print cards using ID software 24
- Print from a PC application 24
- Tips for Success 25
- Viewing and changing 27
- Printing Preferences 28
- Print tab 29
- Priority of Data 31
- 1 Panel Auto 2 Panels 31
- Page Split 32
- Security Erase 33
- Printing Area Settings 34
- Printer Settings 34
- Encode tab 35
- Laminate tab 35
- Configuration tab 35
- Printing Properties 36
- Status Monitor 37
- Close the Status Monitor 38
- Printer Status tab 39
- Printer Setting tab 40
- Retransfer tab 41
- Bend Remedy tab 42
- Media Setting tab 42
- Property tab 43
- Laminator tab 44
- Printer Select tab 45
- Others tab 46
- Security Lock tab 46
- Status monitor messages 47
- “Mending 49
- Using the LCD Menus 55
- Using the Printer LCD Panel 57
- Printer Security Number 63
- Red Status Light 64
- Blue Status Light 64
- Operator Button 64
- “Laminator 65
- LCD messages” on page 84 65
- Laminator Settings 66
- Taking care of your printer 67
- Cleaning the printer 68
- Tips – Cleaning card feed 69
- Cleaning the magnetic head 70
- Cleaning the thermal head 71
- Cleaning printer fan filters 71
- Cleaning the laminator 73
- Laminator fan filter 75
- Messages 77
- Printer error recovery 78
- Transfer jam 79
- Turnover jam 80
- Retransfer section jam 81
- Printer LCD messages 83
- “Operating environment” on 85
- “Load cards” on 85
- Take -up side 86
- Laminate pressure motor 86
- Supply side 86
- Supp ly Roll 87
- Patch Position 88
- Card warping 89
- Laminator LCD messages 90
- Supplies 93
- Ink ribbon 94
- Retransfer film 94
- Laminator material 95
- Cleaning supplies 96
- Site requirements 97
- Site guidelines 98
- Ventilation clearance 99
- Printer specifications 100
- Laminator specifications 101
- Magnetic Stripe Encoding 103
- Inline Encoding 104
- Character Code Table 105
- Compliance (FCC) 107
- Regulatory compliance 108
- 11111 Bren Road West 109
- Minnetonka, MN 55343-9015 109
- 952.933.1223 109
- 952.933.7971 FAX 109
© 2020, manymanuals.es. Todos los derechos reservados | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales